SD PROTECTED - Disaster Recovery and Prevention Solutions

SD Labs offers a unique family of products, services, and equipment to help contractors and consumers clean and disinfect facilities of all types, and continuously control surface damaging and odor-causing mildew, mold, bacteria and algae caused by flooding. 


  • SD Clean - ready to use industrial strength cleaner to remove molds, grease, grime and foreign matter form all types of surfaces.
  • SD VO - ready to use EPA registered hospital grade disinfectant/cleaner to kill germs, mold, fungi, and algae.
  • Electrolyzed Water Equipment to Clean - On-Site Generation of Non-Toxic Cleaning & Degreasing Solutions
  • Electrolyzed Water Equipment to Kill Germs - On-Site Generation of Non-Toxic Disinfecting Solutions
  • Long Lasting Antimicrobial Based Surface Coatings to Inhibit Mold Growth
  • Cost Effective Application Equipment to reduce labor and product costs
  • Equipment, Sales, and Training


SD Product Decriptions

 1. SD Clean


Powerful Cleaning


SD Clean is an industrial strength blend of quat-based surfactants that create a safe but powerful cleaner and degreaser that removes dirt, grease, and grime from hard surfaces. SD Clean leaves behind a fresh scent and no residue. The product can be used full strength, be diluted 2:1 in the field, or shipped in diluted concentrations upon request.

GENERAL INDUSTRIAL APPLICATIONS: Dilute 1 part product with 1 part hot or cold water (or use full strength) and spray or mop on surface. Allow contact time of 1 to 2 minutes and scrub. Wipe with clean towel or mop.

INDUSTRIAL FLOORS AND CONCRETE: Use full strength and apply with mop or pressure sprayer. Scrub using a floor machine or deck brush. Allow a contact time of 1 to 2 minutes but do not allow to dry. Pick up solution with wet pick-up vacuum; a mop and wringer; or flush to floor drain. Rinse thoroughly.

FOR USE IN AUTOMATIC SCRUBBERS: Add to the solution tank at a dilution of one part product with up to one part water, depending on amount of soil. Extremely soiled areas should be pre-treated with SD Clean, mix one part solution to one part water, before scrubbing. Pick up all residues of detergent solution and dissolved soils with vacuum pick-up or rinse thoroughly with mop and wringer.


2. SD Pro


Surface Defense Professional


Surface Defense Pro, SD Pro, is a professional grade surface coating designed to provide ongoing control of bacteria, mold, and algae that can cause surface damage, stains and odors for many years depending on the levels of abrasion the product is subjected to. Apply SD Pro inside wall cavities, on flooring, decking, painted surfaces, siding, glass, metals, or virtually any dried surface. One gallon of product will treat approximately 3,750 square feet of surface area when applied via an electrostatic sprayer. SD Pro is classified as a Treated Article Under US EPA FIFRA regulations and is registered as a long lasting disinfectant in multiple international markets.

  • A year or More of Activity
  • Dries in 1 Hour Or Less, Without Changing Surface Look or Feel
  • Resistant to Most Common Cleaning and Disinfecting Chemicals
  • Applied by Trained Applicators


Application Instructions:
SD Pro is applied using specialty electrostatic equipment provided by SD Labs and is only available to organizations and individuals who have been factory trained on the appropriate application techniques and practices. SD Pro should only be applied to pre-cleaned surfaces free of oil, dirt and other contaminants and be at 50 degrees F or higher to assure proper bonding and a short drying time. The product should be stored at room temperature and not be allowed to freeze.


3. SD-ST 


Surface Defense Short Term

Ready-to-use consumer formula for direct trigger or pump spray application by the consumer or trained technician to
almost any surface. Upon drying, the product leaves behind an invisible, non-tactile coating that inhibits the
growth of a wide variety of surface damaging and odor-causing bacteria, fungi, algae and molds for up to 90 days or more depending on use conditions. The product also controls odors, stains and surface damage caused by these organisms. SD-ST is classified as a Treated Article Under US EPA FIFRA regulations and is registered as a long lasting disinfectant in multiple international markets.

  • Ready to Use Formulation
  • Up to 3 Months of Activity
  • Inhibits Mold, Mildew, and Algae from Flooding
  • Can Be Used on Almost Any Surface


Store at a temperature of 65°F or higher for greatest efficacy. Shake well before each use.

SD-ST APPLICATION INSTRUCTIONS - SURFACES 


Surface must be clean of dirt, dust, and oils prior to application. Test for staining and color- steadfastness of fabric or surface by treating and drying a small concealed area prior to application. Spray entire surface area from a distance of 16 – 24 inches, ensuring complete coverage. Porous substrates and textiles will require greater amounts of product to account for absorption of SD-ST into the treated area. See instructions below for treatment of electronic devices. Lightly wipe after 3 – 5 minutes with a clean microfiber or lint-free cloth. Allow to dry thoroughly. If spotting occurs, moisten a cloth or sponge with SD-ST and wipe the area.

SD-ST APPLICATION INSTRUCTIONS – PERSONAL ELECTRONICS EQUIPMENT


Surface must be clean of dirt, dust, and oils prior to application. Test for staining and color-steadfastness of fabric or surface by treating and drying a small concealed area prior to application. Moisten a clean lint-free microfiber cloth with the product and apply liberally to the surface you wish to treat. Use caution to avoid injecting liquid into sensitive components or openings. Lightly wipe after 3 – 5 minutes with a clean microfiber or lint-free cloth. Allow to dry thoroughly. If spotting occurs, moisten a cloth or sponge with SD-ST and wipe the area. Care should be used not to over-saturate areas which may be sensitive to liquid or spraying into equipment and device.